reduce smoke Daihatsu 2-stroke crankcase
The cylinder head is attached to the engine block by numerous bolts or studs. It has several functions. The cylinder head seals the cylinders on the side opposite to the pistons; it contains short ducts (the ports) for intake and exhaust and the associated intake valves that open to let the cylinder be filled with fresh air and exhaust valves that open to allow the combustion gases to escape. However, 2-stroke crankcase scavenged engines connect the gas ports directly to the cylinder wall without poppet valves; the piston controls their opening and occlusion instead. The cylinder head also holds the spark plug in the case of spark ignition engines and the injector for engines that use direct injection. All CI engines use fuel injection, usually direct injection but some engines instead use indirect injection. SI engines can use a carburetor or fuel injection as port injection or direct injection. Most SI engines have a single spark plug per cylinder but some have 2. A head gasket prevents the gas from leaking between the cylinder head and the engine block. The opening and closing of the valves is controlled by one or several camshafts and springs?or in some engines?a desmodromic mechanism that uses no springs. The camshaft may press directly the stem of the valve or may act upon a rocker arm, again, either directly or through a pushrod.
Engine block seen from below. The cylinders, oil spray nozzle and half of the main bearings are clearly visible.
The crankcase is sealed at the bottom with a sump that collects the falling oil during normal operation to be cycled again. The cavity created between the cylinder block and the sump houses a crankshaft that converts the reciprocating motion of the pistons to rotational motion. The crankshaft is held in place relative to the engine block by main bearings, which allow it to rotate. Bulkheads in the crankcase form a half of every main bearing; the other half is a detachable cap. In some cases a single main bearing deck is used rather than several smaller caps. A connecting rod is connected to offset sections of the crankshaft (the crankpins) in one end and to the piston in the other end through the gudgeon pin and thus transfers the force and translates the reciprocating motion of the pistons to the circular motion of the crankshaft. The end of the connecting rod attached to the gudgeon pin is called its small end, and the other end, where it is connected to the crankshaft, the big end. The big end has a detachable half to allow assembly around the crankshaft. It is kept together to the connecting rod by removable bolts.
The cylinder head has an intake manifold and an exhaust manifold attached to the corresponding ports. The intake manifold connects to the air filter directly, or to a carburetor when one is present, which is then connected to the air filter. It distributes the air incoming from these devices to the individual cylinders. The exhaust manifold is the first component in the exhaust system. It collects the exhaust gases from the cylinders and drives it to the following component in the path. The exhaust system of an ICE may also include a catalytic converter and muffler. The final section in the path of the exhaust gases is the tailpipe.
Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine
Gas turbines
Gas turbines
Main article: gas turbine
Turbine Power Plant
A gas turbine compresses air and uses it to turn a turbine. It is essentially a Jet engine which directs it's output to a shaft. There are three stages to a turbine: 1) air is drawn through a compressor where the temperature rises due to compression, 2) fuel is added in the combuster, and 3) hot air is exhausted through turbines blades which rotate a shaft connected to the compressor.
A gas turbine is a rotary machine similar in principle to a steam turbine and it consists of three main components: a compressor, a combustion chamber, and a turbine. The air, after being compressed in the compressor, is heated by burning fuel in it. About ? of the heated air, combined with the products of combustion, expands in a turbine, producing work output that drives the compressor. The rest (about ?) is available as useful work output. 26
Gas Turbines are among the MOST efficient internal combustion engines. The General Electric 7HA and 9HA turbine electrical plants are rated at over 61% efficiency. 27
Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine
There are several possible ways
Classification
There are several possible ways to classify internal combustion engines.
Reciprocating:
By number of strokes
Two-stroke engine
Clerk Cycle 1879 6
Day Cycle
Four-stroke engine (Otto cycle)
Six-stroke engine
By type of ignition
Compression-ignition engine
Spark-ignition engine (commonly found as gasoline engines)
By mechanical/thermodynamical cycle (these 2 cycles do not encompass all reciprocating engines, and are infrequently used):
Atkinson cycle
Miller cycle
Rotary:
Wankel engine
Continuous combustion:
Gas turbine
Jet engine
Rocket engine
Ramjet
The following jet engine types are also gas turbines types:
Turbojet
Turbofan
Turboprop
Źródło: https://en.wikipedia.org/wiki/Internal_combustion_engine